ALD vs CVD: what is the difference?
ALD grew out of CVD and uses many of the same precursor chemistries, but its cyclic, self-limiting operation gives it very different strengths. As transistors became three-dimensional and memory cells were stacked vertically, ALD moved from a niche technique to a standard tool for the thinnest and most conformal films, while CVD remains the choice for thicker films and gap fill.
The short answer
The difference is how the reaction is controlled. CVD (chemical vapour deposition) supplies reactive gases together, and the film grows continuously at a rate set by temperature, pressure and gas flow. ALD (atomic layer deposition) supplies precursors one at a time, separated by purges, and each surface reaction stops by itself once the surface is saturated, so the film grows by a fixed, sub-nanometre amount per cycle. ALD therefore gives angstrom-level thickness control and uniform coverage of very deep structures, while CVD deposits thicker films much faster.
Side-by-side comparison
| Aspect | ALD | CVD |
|---|---|---|
| Precursor delivery | Sequential pulses of precursor and co-reactant, separated by purges | Reactant gases supplied together and continuously |
| Growth control | Self-limiting surface reactions; thickness = growth per cycle × number of cycles | Thickness set by deposition rate and time, which depend on temperature, pressure and flow |
| Typical growth per cycle or rate | Usually a fraction of a nanometre per cycle, often around 1 Å | From nanometres to hundreds of nanometres per minute |
| Conformality | Excellent, even in high-aspect-ratio trenches and holes | Varies: good for surface-reaction-limited thermal CVD, poorer for most plasma CVD |
| Typical film thickness | Sub-nanometre to a few tens of nanometres | Tens of nanometres to micrometres |
| Throughput | Lower for single wafers; improved by batch furnaces, multi-station chambers and spatial ALD | Higher, especially for thick films |
| Temperature | Thermal ALD usually a few hundred °C; plasma-enhanced ALD can run lower | From below 400 °C for plasma CVD to 600–800 °C or more for thermal LPCVD |
| Typical films | High-k gate dielectrics (HfO₂), work-function metals (TiN), DRAM capacitor dielectrics, SADP spacers, thin liners and barriers | Interlayer dielectrics (SiO₂), silicon nitride, polysilicon, tungsten fill, 3D NAND oxide/nitride stacks |
How an ALD cycle works
A typical ALD cycle has four steps. The first precursor, for example trimethylaluminium, is pulsed into the chamber and reacts with the surface until every available site is occupied; any excess cannot react further. A purge removes the excess. The second reactant, such as water or ozone, then reacts with the adsorbed layer, and a second purge follows. One cycle adds a fixed increment of film, and repeating it tens or hundreds of times builds the target thickness.
Because the reactions saturate, the result depends little on small variations in gas flow or exposure time, provided each pulse is long enough to reach the bottom of a structure. This is why ALD coats deep holes and trenches almost uniformly. Plasma-enhanced ALD replaces the thermal co-reactant with plasma species, allowing lower temperatures and wider choice of materials, but plasma damage and reduced conformality in very deep features must be managed.
How CVD works
In CVD, precursors such as silane, TEOS or tungsten hexafluoride are introduced together and react on, or just above, the heated wafer. Energy comes from heat (thermal CVD and LPCVD) or from a plasma (PECVD). Growth is continuous, so CVD can deposit hundreds of nanometres in minutes.
Conformality depends on the regime. When the surface reaction is slow and controls the rate, as in low-pressure thermal CVD, reactants reach the bottom of features and coverage is good. When the rate is limited by gas transport or by directional plasma species, films are thicker at the top of features, which is why special variants such as HDP-CVD, sub-atmospheric CVD and flowable CVD are used for gap fill.
Which to use when
ALD is the default for films only a few nanometres thick, for layers whose thickness must be controlled to within an angstrom or two, and for coatings inside high-aspect-ratio features: high-k gate dielectrics and metal gates in FinFETs and gate-all-around transistors, DRAM capacitor dielectrics, the charge-trap and blocking layers lining 3D NAND channel holes, and spacers for self-aligned multi-patterning.
CVD is the default for thicker films: interlayer dielectrics, hard masks, the alternating oxide and nitride layers that form a 3D NAND stack, polysilicon and tungsten fill. The two are often combined, for example a thin ALD nucleation layer followed by a CVD tungsten fill.
Where Japanese suppliers fit
Tokyo Electron supplies both CVD and ALD systems, including semi-batch ALD tools, and Kokusai Electric is known for batch vertical furnaces used for LPCVD and ALD. Japanese chemical companies also supply many of the precursors used in both processes.
FAQ
Is ALD a type of CVD?
ALD is often described as a variant of CVD because it uses similar precursors and chemical reactions. The defining difference is that ALD separates the reactants in time so that each surface reaction is self-limiting. In fabs, ALD and CVD are treated as separate process steps, often on different tools.
Why is ALD slower than CVD?
Each cycle adds only around an angstrom of film and includes purge steps, so a 10 nm film can need about a hundred cycles. Equipment makers raise throughput with batch furnaces that process many wafers at once, multi-station chambers and spatial ALD, in which the wafer moves between zones of different gases instead of the gases being switched.
Are 3D NAND layer stacks deposited by ALD?
Mostly not. The alternating oxide and nitride layers that form the stack, each tens of nanometres thick and numbering in the hundreds, are usually deposited by PECVD for speed. ALD is used afterwards for the thin films lining the deep channel holes, such as blocking, charge-trap and tunnel layers.
What is area-selective deposition?
Area-selective deposition uses ALD or CVD chemistry that grows on one surface but not on another, for example on metal but not on dielectric. It could reduce lithography and etch steps by aligning new films to existing patterns, and it builds on the surface control that ALD provides.
Terms compared
- ALD (Atomic Layer Deposition)A deposition method that grows films one sub-atomic-layer cycle at a time using self-limiting surface reactions, giving precise thickness and conformal coverage.
- CVD (Chemical Vapour Deposition)A family of deposition methods in which precursor gases react on a heated or plasma-exposed wafer and leave a solid thin film behind.
- Step CoverageA measure of how evenly a deposited film covers the tops, sidewalls and bottoms of trenches and holes on the wafer.
Japanese companies involved
- Tokyo Electron (TEL) · Coat/develop, etch and deposition equipment
- Kokusai Electric · Batch deposition, diffusion and ALD equipment
- ULVAC · Vacuum deposition (sputtering) equipment and vacuum pumps
More deposition comparisons
Sources
Semiconductor comparisons
- All semiconductor comparisons
- CVD vs PVD: what is the difference?
- PECVD vs LPCVD: what is the difference?
- MOCVD vs MBE: what is the difference?
- Dry etching vs wet etching: what is the difference?
- ICP vs CCP: what is the difference?
- ALE vs RIE: what is the difference?
- Ion implantation vs thermal diffusion: what is the difference?
Last updated: November 2, 2026