ICP vs CCP: what is the difference?
ICP and CCP are the two most common ways of creating the plasma inside dry etchers and plasma CVD tools. Equipment datasheets often just say 'ICP type' or 'CCP type', but the distinction largely determines which films a chamber etches well. The difference starts from how RF power is coupled into the gas, which in turn sets plasma density, operating pressure and how independently ion flux and ion energy can be controlled.
The short answer
ICP (inductively coupled plasma) generates plasma with an RF coil outside a dielectric window, giving dense plasma (about 10¹¹–10¹² cm⁻³) at low pressure, with ion energy set independently by a separate wafer bias. CCP (capacitively coupled plasma) generates plasma between parallel-plate electrodes; its density is one to two orders of magnitude lower, but the electrode sheath readily produces high-energy ions and uniform plasma over large areas. As a rule, silicon, polysilicon and metal etching use ICP, while oxide and nitride dielectric etching uses CCP.
Side-by-side comparison
| Aspect | ICP | CCP |
|---|---|---|
| Plasma generation | RF current in a coil induces an electric field through a dielectric window | RF voltage between parallel-plate electrodes accelerates electrons directly |
| Plasma density | High, roughly 10¹¹–10¹² cm⁻³ | Lower, roughly 10⁹–10¹⁰ cm⁻³ |
| Operating pressure | Low, roughly 1–50 mTorr | Somewhat higher, roughly 10–200 mTorr |
| Density vs ion energy | Set independently by source (coil) power and bias (wafer) power | Coupled through the same electrodes; dual- or multi-frequency designs separate them |
| Ion energy | Can be kept low to minimise damage to underlying layers | Large sheath voltage readily gives high-energy ions |
| Uniformity | Depends on coil and chamber design; large wafers need careful engineering | Parallel plates give uniform plasma over large areas relatively easily |
| Main etch targets | Silicon, polysilicon gates, metal lines, shallow trench isolation, deep silicon | SiO₂ and SiN dielectrics, contacts, vias, high-aspect-ratio holes |
| Typical gases | Halogens such as Cl₂, HBr and SF₆ | Fluorocarbons such as C₄F₈ and CF₄ with oxygen and argon |
| Hardware | Needs a dielectric window and coil; more complex | Simpler structure with fewer parts |
| Deposition use | High-density plasma CVD (HDP-CVD) for gap fill | Standard source for PECVD of SiO₂ and SiN |
How each source makes plasma
In a CCP chamber, RF voltage is applied to one or both of two facing electrodes, and the electric field between them accelerates electrons that ionise the gas. Next to each electrode a sheath forms, a thin layer with a large potential drop, and ions crossing it hit the wafer almost vertically. In a CCP, the field that sustains the plasma and the field that accelerates ions therefore come from the same electrodes.
In an ICP chamber, RF current flows through a coil placed outside a dielectric window. The time-varying magnetic field induces an electric field in the gas that sustains the discharge. Plasma generation happens at the coil, so the electrode under the wafer can be given its own bias supply that only sets how strongly ions are drawn in. Whether density and ion energy can be controlled separately is the starting point for the different character of the two sources.
Why conductor etching uses ICP
Etching gates, silicon fins or metal lines requires vertical profiles and a reliable stop on very thin underlying layers such as gate dielectrics only a few nanometres thick. A dense plasma supplies plenty of radicals and ions, so etch rates remain practical at low pressure, where ions scatter less and travel more directionally. Turning the bias power down then lowers ion energy, protecting the layer underneath and preserving selectivity. High density with low ion energy is the combination ICP delivers naturally.
Why dielectric etching uses CCP
The silicon-oxygen bond in SiO₂ is strong, and chemistry alone etches it very slowly. Dielectric etching relies on ion-assisted reactions: fluorocarbon gases deposit a thin polymer on the surface and energetic ions drive the reaction that removes oxide as volatile products. CCP makes high-energy ions easily and gives good uniformity across the wafer.
Modern dielectric etchers use dual- or multi-frequency CCP, in which a higher frequency mainly sets plasma density and a lower frequency mainly sets ion energy. This has largely removed the coupling that was CCP's main weakness. The deep holes etched through alternating oxide and nitride layers in 3D NAND are an example of this high-ion-energy CCP application.
The boundary is not fixed
ICP for conductors and CCP for dielectrics is a tendency, not a rule. Deep silicon etching for MEMS and through-silicon vias (the Bosch process) and compound semiconductor etching mostly use ICP because they need high density, and ICP chambers for dielectrics exist too. Remote plasma sources and atomic layer etching also fall outside the simple split. When comparing tools, it is more reliable to start from the film, selectivity, aspect ratio and damage tolerance required than from the source name.
FAQ
What is the difference between ICP-RIE and RIE?
RIE (reactive ion etching) names the etching mechanism, combining ions and radicals to etch directionally, and says nothing about how the plasma is produced. Classic parallel-plate RIE tools use CCP; ICP-RIE uses an inductive source for the plasma and a separate bias for the ions. RIE is the mechanism, ICP and CCP are plasma source types.
Is Lam Research's TCP the same as ICP?
TCP (transformer coupled plasma) is Lam Research's name for its inductively coupled source, which places a flat spiral coil on top of a dielectric window. Physically it is a type of ICP.
Is CCP an older, inferior technology?
No. ICP gives higher plasma density, but CCP offers the high ion energy and large-area uniformity that dielectric etching needs, and multi-frequency CCP chambers are used for leading-edge logic and 3D NAND dielectric etching. The two are suited to different films rather than ranked.
Does the ICP/CCP distinction matter in deposition too?
Yes. Standard PECVD of silicon oxide and nitride at low temperature uses CCP. HDP-CVD, which deposits and sputters simultaneously to fill narrow gaps, uses an inductive or other high-density source.
Terms compared
- ICP (Inductively Coupled Plasma)A plasma source that drives RF current through a coil to induce an electric field, giving high-density plasma at low pressure.
- CCP (Capacitively Coupled Plasma)A plasma source that applies RF power between two parallel-plate electrodes, used for dielectric etching and PECVD.
- Plasma DensityThe number of electrons or ions per unit volume in a plasma, usually given per cm³; it largely sets etch and deposition rates.
- RIE (Reactive Ion Etching)The main form of dry etching, in which reactive radicals and ions from a plasma act together to remove material vertically and transfer patterns with straight side walls.
Japanese companies involved
- Tokyo Electron (TEL) · Coat/develop, etch and deposition equipment
- SAMCO · Plasma etching, CVD and plasma cleaning equipment
- Hitachi High-Tech · CD-SEM metrology, defect inspection and etch systems
- Daikin Industries · Etching gases, fluoropolymers and fluoroelastomers
- Kanto Denka Kogyo · Fluorine-based specialty gases
More etching comparisons
Sources
Semiconductor comparisons
- All semiconductor comparisons
- ALE vs RIE: what is the difference?
- Ion implantation vs thermal diffusion: what is the difference?
- Front-end vs back-end process: what is the difference?
- FinFET vs GAA: what is the difference?
- NAND vs DRAM: what is the difference?
- HBM vs GDDR6: what is the difference?
- HBM3E vs HBM4: what is the difference?
Last updated: November 2, 2026