CVD vs PVD: what is the difference?
Chipmaking uses both methods many times over. CVD and its offshoot ALD deposit most dielectric films and some metals, such as tungsten, while PVD, almost always sputtering in front-end fabs, deposits aluminium interconnects, barrier layers and the copper seed for electroplating. The choice depends on the material, the shape of the structure being coated and the thermal budget at that point in the process.
The short answer
The difference is how material reaches the wafer. In CVD (chemical vapour deposition), precursor gases react chemically on or near the heated wafer surface and leave a solid film, which can coat the sides and bottoms of features well. In PVD (physical vapour deposition), atoms are physically removed from a solid source, by sputtering or evaporation, and travel largely in straight lines to the wafer, giving pure metal films at low temperature but thinner coverage inside deep features.
Side-by-side comparison
| Aspect | CVD | PVD |
|---|---|---|
| Principle | Chemical reaction of precursor gases, driven by heat or plasma | Physical transfer of atoms from a solid target or source |
| Main variants | LPCVD, PECVD, SACVD, HDP-CVD, MOCVD; ALD as a cyclic variant | DC and RF magnetron sputtering, ionised PVD, electron-beam and thermal evaporation |
| Step coverage | Good to excellent for thermal and ALD processes; weaker for plasma CVD | Line-of-sight: sidewalls and bottoms of deep features receive less film |
| Wafer temperature | From below 400 °C (PECVD) to 600–800 °C or more (LPCVD) | Room temperature to a few hundred °C |
| Purity and composition | Set by precursor chemistry; by-products such as hydrogen, carbon or chlorine can remain | Close to target composition; alloys and compounds from alloy targets or reactive sputtering |
| Pressure | Roughly 0.1–10 Torr for most CVD; near atmospheric for some | High-vacuum base pressure; sputtering runs at a few mTorr of argon |
| Typical films | SiO₂, Si₃N₄, polysilicon, tungsten, high-k oxides (via ALD) | Aluminium, Ti/TiN, Ta/TaN barriers, copper seed, magnetic films for MRAM |
| Material source | Gas or vaporised liquid precursors | Solid sputtering targets or evaporation sources |
How CVD works
In CVD, precursors such as silane, TEOS, ammonia or tungsten hexafluoride flow into the chamber and react to form a solid film. Thermal CVD and LPCVD rely on heat alone; PECVD uses a plasma to break up the gases so that deposition can run below 400 °C, after metal interconnects are in place. Because reactive species can reach surfaces that the source cannot see directly, CVD can coat the sides and bottoms of trenches, especially when the rate is limited by the surface reaction rather than by gas transport.
ALD takes the chemical approach further by separating the reactants in time, giving near-perfect conformality for very thin films.
How PVD works
In sputtering, the dominant PVD method in semiconductor fabs, argon ions from a plasma bombard a solid target and knock atoms off it. Magnets behind the target confine the plasma to raise the deposition rate, which is why most sputtering is magnetron sputtering. Adding a reactive gas such as nitrogen produces compound films, for example TiN from a titanium target.
Sputtered atoms travel largely in straight lines, so deep holes receive less film on their sidewalls and bottoms. Ionised PVD addresses this by ionising a large share of the sputtered metal and pulling it towards the wafer with a bias, improving bottom coverage in vias. Evaporation, the other PVD family, heats a source in high vacuum and is used mainly for lift-off metallisation, compound semiconductors and some packaging steps.
Which to use when
Dielectric films and anything that must coat deep structures uniformly usually come from CVD or ALD. Metals that need high purity, low resistivity or low process temperature usually come from PVD. Interconnects show the division clearly: in a copper process, PVD deposits the TaN/Ta barrier and the copper seed, and electroplating fills the trench; in contacts, a Ti/TiN liner is followed by CVD tungsten fill, because CVD fills narrow holes that sputtering cannot.
As dimensions shrink, ALD and CVD are taking over some layers that PVD once handled, such as the thinnest barriers and liners, because sputtered films become too uneven in very narrow features.
Where Japanese suppliers fit
Japan has a strong group of sputtering equipment makers, including ULVAC, Canon Anelva and Shibaura Mechatronics, and JX Advanced Metals is a major supplier of sputtering targets. On the CVD side, Tokyo Electron and Kokusai Electric supply deposition systems, including batch furnaces.
FAQ
Is sputtering CVD or PVD?
Sputtering is PVD. Atoms are ejected from a solid target by ion bombardment and deposit on the wafer without a chemical reaction being needed to form the film. Reactive sputtering, in which a gas such as nitrogen combines with the sputtered metal, is still classed as PVD.
Which has better step coverage, CVD or PVD?
In general CVD, and particularly ALD, coats steps and trenches more uniformly. PVD is a line-of-sight process, so deep features receive thinner film on their sidewalls and bottoms. Ionised PVD and re-sputtering techniques improve coverage but do not reach the conformality of ALD.
Why is copper not deposited by CVD?
Copper CVD has been researched, but in production the trenches are filled by electroplating, which needs a thin conductive seed. PVD deposits that copper seed, together with the TaN/Ta barrier beneath it, because sputtered copper is pure and adheres well.
What vacuum levels do they need?
Sputtering chambers are pumped to high vacuum before processing to keep films pure, then run at a few millitorr of argon. Most CVD processes run at much higher pressures, from about 0.1 Torr for LPCVD to several Torr for PECVD, and some CVD processes operate near atmospheric pressure.
Terms compared
- CVD (Chemical Vapour Deposition)A family of deposition methods in which precursor gases react on a heated or plasma-exposed wafer and leave a solid thin film behind.
- SputteringA physical vapour deposition method in which ions from a plasma knock atoms out of a target, which then coat the wafer as a thin film.
- Vacuum Evaporation (E-beam Evaporation)A PVD method that heats a material in vacuum until it evaporates, letting the vapour condense on the substrate as a thin film.
Japanese companies involved
- Tokyo Electron (TEL) · Coat/develop, etch and deposition equipment
- Kokusai Electric · Batch deposition, diffusion and ALD equipment
- ULVAC · Vacuum deposition (sputtering) equipment and vacuum pumps
- Canon ANELVA · Sputtering and vacuum deposition equipment
- Showa Shinku · Vacuum evaporation, plasma cleaning and ion beam trimming equipment
- Shincron · Vacuum evaporation and sputtering systems
More deposition comparisons
Sources
Semiconductor comparisons
- All semiconductor comparisons
- PECVD vs LPCVD: what is the difference?
- MOCVD vs MBE: what is the difference?
- Dry etching vs wet etching: what is the difference?
- ICP vs CCP: what is the difference?
- ALE vs RIE: what is the difference?
- Ion implantation vs thermal diffusion: what is the difference?
- Front-end vs back-end process: what is the difference?
Last updated: November 2, 2026