Dry etching vs wet etching: what is the difference?
Etching removes material from the wafer, either everywhere or only where a mask leaves it exposed. Early integrated circuits were patterned almost entirely with wet chemistry, but as feature sizes fell below a few micrometres the sideways etching of wet processes became a limit, and plasma-based dry etching took over pattern transfer. Wet processing did not disappear: it moved to the many steps where selectivity and a damage-free surface matter more than profile control.
The short answer
Dry etching removes material with reactive gases and plasma in a vacuum chamber; ions striking the wafer make the etch directional, so patterns can be transferred with vertical sidewalls at nanometre scale. Wet etching dissolves material in liquid chemicals; it is usually isotropic, undercutting the mask, but it is highly selective, gentle on the surface and inexpensive per wafer. Modern fabs use dry etching for critical pattern transfer and wet processing for cleaning, stripping and blanket film removal.
Side-by-side comparison
| Aspect | Dry etching | Wet etching |
|---|---|---|
| Etchant | Reactive gases excited into a plasma (ions and radicals), or reactive vapours | Liquid chemicals such as hydrofluoric acid, phosphoric acid or alkaline solutions |
| Environment | Low-pressure vacuum chamber with RF power | Baths or single-wafer spin processors at or near atmospheric pressure |
| Directionality | Can be strongly anisotropic because ions arrive perpendicular to the wafer | Generally isotropic; crystal-orientation-dependent etches of silicon are an exception |
| Pattern fidelity | Suited to nanometre-scale patterns and high aspect ratios | Undercuts the mask by roughly the etch depth, limiting use for fine patterns |
| Selectivity | Moderate to high, tuned by gas chemistry and ion energy | Often very high, because chemistry attacks one material and barely touches another |
| Surface damage | Ion bombardment and charging can damage or contaminate the surface | No ion damage; gentle on sensitive surfaces |
| Throughput and cost | Single-wafer tools with vacuum, RF and gas systems; higher cost per step | Batch or fast single-wafer processing; lower equipment cost per step |
| Waste and utilities | Exhaust gases, including fluorinated gases, need abatement | Large volumes of chemicals and rinse water need supply, recycling and waste treatment |
| Typical uses | Gate, fin, contact, via and trench patterning; hard-mask opening; deep silicon etching | Native oxide removal, sacrificial layer removal, resist and residue stripping, wafer cleaning |
How dry etching achieves vertical profiles
In a plasma etcher, RF power breaks feed gases such as fluorocarbons, chlorine or hydrogen bromide into ions and chemically active radicals. The radicals react with the film to form volatile products, and ions accelerated across the sheath above the wafer strike it almost vertically. Ion bombardment speeds up the reaction on horizontal surfaces far more than on sidewalls, and passivating layers deposited on the sidewalls protect them further. The result is anisotropic etching, usually called reactive ion etching (RIE).
This directionality is what allows a resist or hard-mask pattern to be transferred into the film with almost no loss of width, and what makes high-aspect-ratio structures possible. The price is complexity: gas chemistry, pressure, RF power and wafer temperature must be balanced to control profile, selectivity, uniformity and damage.
Where wet etching remains essential
Liquid etchants work by pure chemistry, so they etch in all directions and tend to round off profiles. That same chemistry can be extremely selective. Dilute hydrofluoric acid removes silicon dioxide while leaving silicon almost untouched, and hot phosphoric acid removes silicon nitride selectively to oxide. Wet steps also leave no ion damage, which is important just before gate dielectric formation or epitaxy.
In today's fabs wet processing is used mainly for cleaning, removing native oxide, stripping resist and post-etch residues, removing sacrificial or blanket films and preparing surfaces. Anisotropic wet etching of crystalline silicon in alkaline solutions such as potassium hydroxide is also widely used in MEMS, where the etch follows crystal planes.
Which to use when
If the step must transfer a fine pattern with controlled sidewalls, dry etching is the default. If the step removes an entire layer, must stop on a very thin underlying film, or must avoid surface damage, wet etching is often the better choice. Many process flows combine the two: a dry etch defines the pattern and a short wet clean removes residues and damaged material.
Between the two sit vapour-phase and remote-plasma etches that supply chemistry without ion bombardment. They are used for highly selective isotropic removal, for example of sacrificial layers in three-dimensional transistor and memory structures, where liquids can cause pattern collapse during drying.
FAQ
Why did dry etching replace wet etching for patterning?
Wet etching undercuts the mask by roughly as much as it etches downward. When feature widths became comparable to film thicknesses, that sideways loss made dimensions impossible to control. Plasma etching removes material mainly in the vertical direction, so the pattern keeps its width.
Is wet etching always isotropic?
Not always. Amorphous films such as silicon dioxide etch isotropically, but crystalline silicon in alkaline etchants such as KOH or TMAH etches much more slowly on (111) planes, producing angled or vertical facets. This is used to make MEMS cavities and membranes.
Can dry etching be isotropic?
Yes. When ion bombardment is minimised, for example in downstream or remote plasma etchers, radicals etch in all directions. Isotropic dry etching is used for resist ashing and for selective removal of sacrificial materials.
Which is better for the environment?
Each has its own burden. Dry etching uses fluorinated gases, some with high global warming potential, that require abatement. Wet processing consumes large volumes of chemicals and ultrapure water that must be treated or recycled. Fabs address both through abatement systems and chemical and water reclamation.
Terms compared
- Dry EtchingEtching that removes material in the gas phase with plasma or reactive gases; the main way fine patterns are carved into wafers.
- Isotropic and Anisotropic EtchingIsotropic etching removes material equally in all directions; anisotropic etching removes it mainly downward with little sideways etching.
- EtchingThe front-end process that removes a film where the resist mask is open, carving the lithography pattern into the wafer.
- Etch SelectivityThe ratio between the etch rate of the film being removed and that of the mask or underlying layer that must remain.
Japanese companies involved
- Hitachi High-Tech · CD-SEM metrology, defect inspection and etch systems
- Tokyo Electron (TEL) · Coat/develop, etch and deposition equipment
- SAMCO · Plasma etching, CVD and plasma cleaning equipment
- SCREEN Holdings · Wafer cleaning, coat/develop and inspection equipment
- Kanto Chemical · High-purity process chemicals for cleaning, etching and CMP
- Daikin Industries · Etching gases, fluoropolymers and fluoroelastomers
More etching comparisons
Sources
Semiconductor comparisons
- All semiconductor comparisons
- ICP vs CCP: what is the difference?
- ALE vs RIE: what is the difference?
- Ion implantation vs thermal diffusion: what is the difference?
- Front-end vs back-end process: what is the difference?
- FinFET vs GAA: what is the difference?
- NAND vs DRAM: what is the difference?
- HBM vs GDDR6: what is the difference?
Last updated: November 2, 2026