FinFET vs GAA: what is the difference?
FinFETs replaced planar transistors in leading-edge logic in the early 2010s, beginning with Intel's 22nm process in 2011, and were used by foundries through the 5nm and 3nm generations. GAA nanosheet transistors are their successor: Samsung began 3nm GAA production in 2022, TSMC uses nanosheets from its N2 process, and Intel uses its RibbonFET GAA design in Intel 18A. The change affects device performance, design rules and the equipment fabs need.
The short answer
In a FinFET the gate covers a thin vertical silicon fin on three sides; in a gate-all-around (GAA) transistor the gate surrounds each channel completely, usually a stack of horizontal silicon nanosheets. Wrapping the channel on all sides gives stronger electrostatic control, so leakage stays low as dimensions shrink, and sheet width can be varied continuously rather than in whole fins. GAA is harder to build, adding Si/SiGe superlattice epitaxy, selective SiGe removal and gate deposition between the sheets.
Side-by-side comparison
| Aspect | FinFET | GAA (nanosheet) |
|---|---|---|
| Gate coverage | Three sides of a vertical fin | All sides of each channel |
| Channel shape | Thin vertical fin of silicon | Stack of horizontal nanosheets (or nanowires) |
| Electrostatic control | Much better than planar, but limited as fins narrow | Strongest of the mainstream structures; better suppression of short-channel effects |
| Drive-current tuning | Discrete steps by changing the number of fins | Continuous by changing sheet width, plus number of stacked sheets |
| Key process steps | Fin patterning and etch, replacement metal gate | Si/SiGe superlattice epitaxy, inner spacers, selective SiGe release, gate fill between sheets |
| Process maturity | Mature, with an established equipment and design ecosystem | Newer; more steps and tighter control of thin layers |
| Leading-edge use | From Intel 22nm (2011) to foundry 5nm and TSMC 3nm (N3) | Samsung 3nm (2022), TSMC N2, Intel 18A |
Why the industry moved beyond FinFET
As gate length shrinks, the drain begins to influence the channel almost as strongly as the gate, causing leakage and poor switching; these are short-channel effects. A FinFET improves control by wrapping the gate over a fin, but the bottom of the fin remains connected to the substrate and only three sides are covered. Making fins thinner and taller helps, yet fin width and height approach practical limits for variability and mechanical stability.
A GAA transistor surrounds every channel with gate. Electrostatic control improves, which allows the gate length or supply voltage to scale further for the same leakage. Stacking several sheets vertically delivers drive current within a small footprint.
Design flexibility of nanosheets
In a FinFET, all fins on a process have the same dimensions, so drive strength can only be changed by using more or fewer fins. In a nanosheet process, the sheet width is drawn by the designer, so a high-performance transistor can use wider sheets and a low-power transistor narrower ones within the same technology. This continuous tuning is one of the main practical advantages of GAA for chip designers.
What changes in the fab
A nanosheet flow starts by growing alternating layers of silicon and silicon-germanium by epitaxy. The stack is patterned into fins, a dummy gate is formed, and the SiGe ends are recessed and refilled with inner spacers to isolate the gate from the source and drain. After source and drain epitaxy, the dummy gate is removed and the SiGe layers are etched away with very high selectivity to silicon, releasing the nanosheets.
Finally, gate dielectric and work-function metals must be deposited uniformly in the narrow gaps between and around the sheets, which relies on atomic layer deposition. Selective isotropic etching, precise epitaxy, ALD and metrology able to see buried layers therefore become more important than in FinFET flows.
FAQ
When did GAA go into production?
Samsung announced the start of production of its 3nm process with GAA transistors, which it calls MBCFET, in 2022. TSMC's N2 process uses nanosheet transistors, and Intel 18A uses its RibbonFET design, another GAA nanosheet architecture.
What is the difference between nanosheets and nanowires?
Both are GAA channels. A nanowire is narrow in both directions, like a thin rod; a nanosheet is wider than it is thick. Nanosheets carry more current per stack and their width can be varied, which is why production GAA transistors use them.
Is FinFET obsolete?
No. FinFETs remain in volume production at many nodes, including TSMC's 3nm family, and will be used for years in products that do not need the newest node. GAA is replacing FinFET only at the leading edge.
What comes after GAA nanosheets?
Research is focused on forksheet transistors, which place a dielectric wall between n-type and p-type sheets to pack them more closely, and complementary FETs (CFETs), which stack n-type and p-type transistors on top of each other. Backside power delivery, which moves power wiring to the back of the wafer, is being introduced alongside GAA.
Terms compared
- FinFETA three-dimensional transistor in which the channel is a thin vertical fin wrapped by the gate on three sides; the standard logic transistor from the 22 nm to the 3 nm generation.
- GAA (Gate-All-Around)A transistor structure in which the gate surrounds the channel on all sides, giving better control than a FinFET; used from the 2nm generation.
- Nanosheet TransistorA gate-all-around transistor whose channel is a stack of thin horizontal silicon sheets, each fully wrapped by the gate; used from the 2nm generation.
Japanese companies involved
- Rapidus · Leading-edge logic foundry (2 nm, in development)
- Tokyo Electron (TEL) · Coat/develop, etch and deposition equipment
More devices and process nodes comparisons
Sources
Semiconductor comparisons
- All semiconductor comparisons
- NAND vs DRAM: what is the difference?
- HBM vs GDDR6: what is the difference?
- HBM3E vs HBM4: what is the difference?
- SiC vs GaN: what is the difference?
- SiC vs silicon: what is the difference?
- Gallium oxide vs SiC: what is the difference?
- SiC MOSFET vs IGBT: what is the difference?
Last updated: November 2, 2026