SiC vs GaN: what is the difference?
SiC and GaN are often grouped together as the successors to silicon in power electronics. Their bandgaps are similar, but their crystal quality, device structures and substrates differ, and those differences, rather than bandgap alone, decide where each one is used.
The short answer
Both are wide-bandgap semiconductors that outperform silicon in power conversion, but they suit different voltage ranges. Silicon carbide (SiC) is used for vertical MOSFETs and diodes at roughly 650 V to 3.3 kV and handles heat well, so it dominates EV traction inverters and industrial drives. Gallium nitride (GaN) is mostly used as lateral high-electron-mobility transistors (HEMTs) at up to about 650 V, where its very fast switching shrinks chargers, server power supplies and RF amplifiers.
Side-by-side comparison
| Aspect | SiC | GaN |
|---|---|---|
| Bandgap | About 3.26 eV (4H-SiC) | About 3.4 eV |
| Critical electric field | About 2.5 to 3 MV/cm, roughly ten times silicon | About 3.3 MV/cm |
| Thermal conductivity | High, around three times silicon | Lower, similar to silicon |
| Main power device | Vertical MOSFET and Schottky barrier diode | Lateral HEMT using a two-dimensional electron gas |
| Typical voltage range | About 650 V to 3.3 kV in commercial devices | Mostly 100 V to 650 V; higher-voltage parts are emerging |
| Switching speed | Fast, well beyond silicon IGBTs | Faster still, with very low gate and output charge |
| Substrate | SiC wafers, mainly 150 mm with 200 mm ramping | Usually GaN epitaxy on silicon (150 to 200 mm); GaN on SiC for RF |
| Key process steps | Thick epitaxy, hot ion implantation, activation anneal above 1,600 °C | MOCVD heteroepitaxy of GaN and AlGaN, normally-off gate engineering |
| Typical uses | EV traction inverters, on-board chargers, solar inverters, railway, industrial drives | USB-C chargers, server and telecom power supplies, LiDAR drivers, 5G and radar RF amplifiers |
How SiC devices work
SiC is grown as bulk crystals and sliced into wafers, so power devices can be built vertically: current flows from the top surface down through a thick, lightly doped drift layer to the backside. A thicker drift layer supports higher voltage, which is why SiC scales naturally to 1200 V, 1700 V and 3.3 kV. Its high thermal conductivity lets heat spread out of the chip quickly, an advantage in compact inverters carrying hundreds of amperes.
The main drawbacks are wafer cost and gate-oxide quality. SiC crystals are grown by sublimation at temperatures above 2,000 °C and grow slowly, and the SiC-to-oxide interface traps charge, lowering channel mobility in MOSFETs. Both have improved steadily, and 200 mm SiC wafers are entering production.
How GaN devices work
In a GaN HEMT, a thin AlGaN layer on top of GaN creates a sheet of high-mobility electrons at the interface, the two-dimensional electron gas. Current flows laterally along this channel without doping, so on-resistance and capacitance are very low and the device can switch extremely fast. Because the basic HEMT is normally on, power devices use a p-GaN gate or a cascode with a silicon MOSFET to make it normally off.
GaN for power is usually grown on ordinary silicon wafers, which keeps substrate cost low and allows production in converted silicon fabs. The lateral structure and the thin epitaxial layers allowed on silicon, however, make very high voltages harder, which is why most GaN power transistors are rated at 650 V or below. For RF, GaN grown on semi-insulating SiC substrates combines GaN's electron transport with SiC's heat conduction.
Which to use when
Above roughly 1000 V, at high current or where cooling is constrained, SiC is the usual choice: EV traction inverters with 800 V batteries, industrial motor drives, railway and solar inverters. Below about 650 V, where switching frequency drives the size of magnetics and capacitors, GaN often wins: laptop and phone chargers, data-centre power supplies and 48 V converters. The 650 V class is contested, and choice there depends on cost, frequency and thermal design.
Japanese companies are active in both. ROHM, Mitsubishi Electric, Toshiba and Fuji Electric make SiC power devices, ROHM's group includes the SiC substrate maker SiCrystal, and Resonac supplies SiC epitaxial wafers. ROHM also offers GaN power devices, and Sumitomo Electric is a long-standing maker of GaN-on-SiC RF transistors for base stations.
FAQ
Why are SiC wafers more expensive than GaN-on-silicon wafers?
SiC cannot be melted at normal pressure, so crystals are grown by sublimation at over 2,000 °C, slowly and with defects that must be controlled, and the very hard material is slow to slice and polish. GaN for power devices is grown as a thin epitaxial layer on standard silicon wafers, which are cheap and available in large diameters.
Will GaN replace SiC in electric vehicles?
Not in the traction inverter for the foreseeable future, because those run at 400 to 800 V battery voltages with high currents and temperatures, which suit vertical SiC devices. GaN is being adopted in on-board chargers and DC-DC converters, where its fast switching reduces size.
Is GaN only used for power devices?
No. GaN is also the basis of blue and white LEDs and blue laser diodes, and GaN HEMTs are widely used as RF power amplifiers in mobile base stations, radar and satellite communications.
Terms compared
- Silicon Carbide (SiC)A wide-bandgap compound of silicon and carbon whose high breakdown field and thermal conductivity make it the leading material for high-voltage power devices.
- Gallium Nitride (GaN)A III-V wide-bandgap semiconductor used for blue and white LEDs, fast power transistors and high-power RF amplifiers.
- Wide Bandgap Semiconductor (WBG)Semiconductor materials with a bandgap much wider than silicon's, mainly SiC and GaN, used for efficient high-voltage, high-temperature and high-frequency devices.
- High Electron Mobility Transistor (HEMT)A field-effect transistor whose channel is a two-dimensional electron gas at a heterojunction, giving high mobility for RF amplifiers and GaN power devices.
Japanese companies involved
- ROHM · SiC and silicon power devices, analog ICs
- Resonac · CMP slurries, packaging materials and SiC epitaxial wafers
- Mitsubishi Electric (power devices) · IGBT and SiC power modules, RF and optical devices
- Sumitomo Electric Industries (compound semiconductors) · SiC epitaxial wafers and GaAs and InP substrates
- Nichia · LEDs and laser diodes
More power semiconductors comparisons
Sources
Semiconductor comparisons
- All semiconductor comparisons
- SiC vs silicon: what is the difference?
- Gallium oxide vs SiC: what is the difference?
- SiC MOSFET vs IGBT: what is the difference?
- CoWoS vs SoIC: what is the difference?
- CoWoS vs InFO: what is the difference?
- Chiplet vs monolithic: what is the difference?
- Hybrid bonding vs flip chip: what is the difference?
Last updated: November 2, 2026