Gallium oxide vs SiC: what is the difference?
SiC is already the established wide-bandgap material for high-voltage power devices, used in electric vehicles, solar inverters and industrial drives. Gallium oxide is one of the ultra-wide-bandgap materials studied as a possible next step, alongside aluminium nitride and diamond. Comparing the two shows what Ga2O3 could add and what still stands in the way.
The short answer
Gallium oxide (beta-Ga2O3) has a bandgap of about 4.8 eV, much wider than the 3.3 eV of silicon carbide, which in theory allows higher breakdown voltage and lower loss, and its crystals can be grown from a melt, promising cheaper large substrates. But it conducts heat about ten times worse than SiC and cannot practically be doped p-type. SiC is a mature material with MOSFETs and diodes in volume production, while gallium oxide is at the stage of early diode products and transistor development.
Side-by-side comparison
| Aspect | Gallium oxide (beta-Ga2O3) | SiC (4H-SiC) |
|---|---|---|
| Bandgap | About 4.8 to 4.9 eV | About 3.26 eV |
| Estimated critical electric field | About 8 MV/cm (theoretical) | About 2.5 to 3 MV/cm |
| Electron mobility | Low, around 200 cm²/(V·s) | About 900 to 1,000 cm²/(V·s) |
| Thermal conductivity | Very low, roughly one tenth of SiC | High, about three times silicon |
| Bulk crystal growth | From a melt (EFG and other melt methods) | Sublimation above 2,000 °C; cannot be melted at normal pressure |
| Substrate cost outlook | Potentially low, but volumes are still small | High, though falling as 200 mm wafers ramp |
| p-type doping | Not practical; devices are n-type only | Both n-type and p-type available |
| Device maturity | Schottky diodes at early commercial stage; transistors in development | MOSFETs and Schottky diodes in volume production |
| Expected uses | High-voltage, cost-sensitive power conversion | EV inverters and chargers, solar, railway, industrial drives |
Why a wider bandgap matters
The voltage a power device can block depends on the critical electric field of its material, and that field rises steeply with bandgap. A higher critical field lets the drift layer that holds the voltage be thinner and more heavily doped, which lowers on-resistance. Because the theoretical drift-layer resistance scales with the cube of the critical field, Ga2O3's figure of merit for this trade-off is estimated to be several times that of SiC, even though its electron mobility is lower.
These are theoretical limits. Real devices are limited by edge termination, defects and packaging, and SiC devices have had decades of engineering to approach their limits, while Ga2O3 devices are still far from theirs.
Substrates: Ga2O3's main promise
SiC sublimes rather than melts, so bulk crystals are grown slowly by vapour transport at over 2,000 °C, and controlling dislocations is difficult; this is the main reason SiC devices remain expensive. Beta-Ga2O3 can be grown from a melt, for example by edge-defined film-fed growth, in principle allowing faster growth of large crystals, similar in concept to silicon and sapphire.
Japan has been at the centre of this work. Novel Crystal Technology has developed melt-grown Ga2O3 substrates and epitaxial wafers, and FLOSFIA has worked on corundum-structured alpha-Ga2O3 films grown by mist CVD. Whether Ga2O3 substrates reach low cost in volume is still to be shown.
Heat and p-type: the two hurdles
Ga2O3 conducts heat poorly, so heat builds up in the active region. Approaches include thinning the chip and bonding it to a highly conductive substrate, or cooling it from both sides. SiC, by contrast, is one of the best thermal conductors among semiconductors, which is a real advantage in compact, high-current modules.
No practical p-type Ga2O3 exists, which rules out conventional pn junctions and the inversion-channel MOSFETs used in SiC. Development has therefore focused on Schottky barrier diodes and on n-type-only transistors such as depletion or fin structures, sometimes combined with p-type layers of other oxides. For the foreseeable future SiC remains the mainstream high-voltage material, with Ga2O3 a candidate for specific applications if cost and reliability are proven.
FAQ
Are gallium oxide power devices on the market?
Only on a small scale. Schottky barrier diodes have reached early commercial and sampling stages, while transistors remain in development. Volumes are far below those of SiC devices.
How is gallium oxide different from GaN?
Both contain gallium, but GaN (about 3.4 eV) forms high-electron-mobility transistors suited to fast switching and RF, while Ga2O3 has a wider bandgap but much lower electron mobility, so it is aimed at high-voltage power conversion rather than high frequency.
How does diamond compare with gallium oxide and SiC?
Diamond has an even wider bandgap (about 5.5 eV) and the highest thermal conductivity of any material, so on paper it is the strongest power semiconductor. Doping, substrate size and cost are much harder problems than for Ga2O3, so it is further from commercial use.
Terms compared
- Wide Bandgap Semiconductor (WBG)Semiconductor materials with a bandgap much wider than silicon's, mainly SiC and GaN, used for efficient high-voltage, high-temperature and high-frequency devices.
- Silicon Carbide (SiC)A wide-bandgap compound of silicon and carbon whose high breakdown field and thermal conductivity make it the leading material for high-voltage power devices.
- SiC Wafer (Silicon Carbide Substrate)A single-crystal silicon carbide substrate for power devices, grown by sublimation rather than from a melt, which makes it slow and costly to produce.
- Breakdown VoltageThe maximum voltage a power device can block in the off state before avalanche breakdown, set mainly by drift-layer thickness and doping.
Japanese companies involved
- ROHM · SiC and silicon power devices, analog ICs
- Mitsubishi Electric (power devices) · IGBT and SiC power modules, RF and optical devices
- Resonac · CMP slurries, packaging materials and SiC epitaxial wafers
- Sumitomo Electric Industries (compound semiconductors) · SiC epitaxial wafers and GaAs and InP substrates
- DISCO · Dicing, grinding and polishing equipment
- Komatsu NTC · Wire saws for slicing silicon and SiC ingots
- Takatori · Wire saws, dicing-related equipment and bonding/debonding systems
- Mitsuboshi Diamond Industrial · Scribe-and-break cutting systems and scribing wheels
More power semiconductors comparisons
Sources
Semiconductor comparisons
- All semiconductor comparisons
- SiC MOSFET vs IGBT: what is the difference?
- CoWoS vs SoIC: what is the difference?
- CoWoS vs InFO: what is the difference?
- Chiplet vs monolithic: what is the difference?
- Hybrid bonding vs flip chip: what is the difference?
- TSV vs wire bond: what is the difference?
- Wafer test vs final test: what is the difference?
Last updated: November 2, 2026