Exhibiting at SEMICON Japan 2026 (Dec 9–11)? We are now accepting advertising inquiries from exhibitors.Ads for SEMICON Japan 2026Learn more

Comparison · Power semiconductors

SiC MOSFET vs IGBT: what is the difference?

The IGBT (insulated-gate bipolar transistor) has been the standard high-voltage switch in motor drives, inverters, railway traction and electric vehicles since the late 1980s. SiC MOSFETs have taken over a growing share of EV traction inverters, on-board chargers and solar inverters, especially in 800 V systems. The choice now turns on efficiency, switching frequency and cost.

The short answer


A SiC MOSFET is a unipolar transistor made of silicon carbide; an IGBT is a bipolar-assisted silicon transistor. Because the SiC MOSFET conducts with electrons only, it has no tail current at turn-off, so switching losses are much lower and it can run at tens to hundreds of kilohertz, and its resistive on-state lowers loss at light load. The silicon IGBT has a fixed on-state voltage drop and higher switching loss, but it is cheaper, robust and well proven at high current and voltage.

Side-by-side comparison


AspectSiC MOSFETSilicon IGBT
Material and carriersSilicon carbide; unipolar (electrons only)Silicon; bipolar conduction (electrons and holes)
On-state behaviourResistive (RDS(on)); loss falls sharply at partial loadFixed knee voltage plus slope (VCE(sat)); loss does not fall as much at light load
Turn-offNo tail current; very low switching lossTail current while stored carriers recombine
Typical switching frequencyTens to hundreds of kHzA few kHz to about 20 kHz in power converters
Reverse conductionBuilt-in body diode, or synchronous conduction through the channelNeeds a separate anti-parallel diode
Common voltage classes650 V, 1200 V, 1700 V; 3.3 kV in some modules600 V to 6.5 kV
Maximum junction temperatureTypically 175 °C in commercial partsTypically 150 to 175 °C
Gate driveHigher and often asymmetric gate voltages; fast edges need careful layoutMature, tolerant gate drive
CostHigher, driven by SiC wafer and process costLower, on mature silicon processes
Typical usesEV traction inverters, on-board chargers, DC-DC converters, solar inverters, fast chargersIndustrial drives, railway traction, UPS, welding, many EV and hybrid inverters

Why the SiC MOSFET switches with less loss


An IGBT is a MOSFET combined with a bipolar transistor. When it is on, holes are injected into the drift region and lower its resistance, which keeps conduction loss low even at high voltage. At turn-off those stored carriers must recombine before the current stops, so a tail current flows while the voltage is already high. That tail is the main reason IGBT switching losses are high and switching frequencies are kept low.

Silicon carbide's breakdown field is about ten times that of silicon, so a SiC device can hold 1200 V with a thin, low-resistance drift layer without carrier injection. The SiC MOSFET therefore stays unipolar, turns off without a tail and can switch much faster. Higher frequency allows smaller inductors, capacitors and filters, and lower loss allows smaller heat sinks.

Conduction loss and partial load


An IGBT's on-state voltage has a knee of roughly a volt before current rises, so even small currents produce noticeable loss. A MOSFET behaves like a resistor, so loss falls with the square of the current. Since EV traction inverters spend most of their time at partial load, this matters: SiC inverters reduce losses most in typical driving rather than at peak power, which extends range for a given battery or allows a smaller one.

At very high current an IGBT's voltage drop can match or beat a SiC MOSFET of the same chip area, and IGBT modules have long field records in railway and industrial drives. SiC MOSFETs also bring new design issues: faster voltage edges increase electromagnetic interference and stress motor insulation, and the gate oxide needs careful reliability qualification.

Which to use when


SiC MOSFETs fit where efficiency, power density and high switching frequency justify a higher device price: 800 V EV traction inverters, on-board chargers, fast DC chargers, solar and storage inverters, and server power supplies above the GaN voltage range. IGBTs remain the economical choice for cost-sensitive EVs and hybrids, industrial drives, welding, UPS and very high-power converters where switching frequency is low anyway. Some inverters combine both, using SiC and IGBT chips in parallel.

Japan is strong in both technologies. Mitsubishi Electric, Fuji Electric, Toshiba and Hitachi Power Semiconductor Device are long-standing IGBT module makers, and ROHM, Mitsubishi Electric, Toshiba, Fuji Electric and Denso produce SiC MOSFETs and modules.

FAQ


Is there a silicon carbide IGBT?

SiC IGBTs have been demonstrated for ultra-high voltages, around 10 kV and above, where even SiC MOSFETs would need very thick drift layers. They are research and niche devices; commercial SiC power transistors are almost all MOSFETs.

Why are SiC MOSFETs more expensive than IGBTs?

SiC wafers are grown slowly by sublimation and are costly and small, defect control is harder, and processing needs high-temperature ion implantation and activation anneals above 1,600 °C. Silicon IGBTs are made on cheaper, larger wafers with mature processes.

Do all electric vehicles use SiC inverters?

No. SiC is common in 800 V platforms and in vehicles where efficiency and range justify the cost, while many vehicles, particularly lower-cost models and hybrids, still use silicon IGBT inverters.

Terms compared


Japanese companies involved


More power semiconductors comparisons


Sources


  1. Toshiba Electronic Devices & Storage: SiC MOSFETs for downsizing and low-loss power supplies (Japanese)
  2. Tokyo Electron nanotec museum: glossary, IGBT (Japanese)
  3. ROHM TechWeb: What is an IGBT? (Japanese)

More on this topic


Semiconductor comparisons

Power semiconductors terms

Last updated: November 2, 2026