HTOL vs burn-in: what is the difference?
The two are easy to confuse because the stress conditions look similar. The distinction becomes clear when you ask what each produces: burn-in produces screened products, while HTOL produces evidence that a design and process are reliable enough. That difference drives sample size, duration, timing and who pays for the test.
The short answer
Both run devices hot and under bias, but for opposite purposes. Burn-in is a production screen: parts are stressed for hours so that units with latent defects fail in the factory and are removed, leaving good parts to ship. HTOL (high temperature operating life) is a qualification test: a sample is stressed for around 1,000 hours to estimate wear-out lifetime and failure rate in FIT, and the stressed parts are not shipped.
Side-by-side comparison
| Aspect | Burn-in | HTOL |
|---|---|---|
| Purpose | Screen out early-life (infant mortality) failures | Estimate lifetime and failure rate |
| Bathtub curve region | Consumes the early-failure region on the left | Checks that wear-out on the right starts well after the required life |
| Devices tested | All production parts, or a sample when the process is mature | A limited sample from several lots |
| Typical duration | A few hours to a few tens of hours | Around 1,000 hours |
| Typical temperature | Around 125°C with raised voltage | Around 125°C junction temperature with bias at or above maximum operating voltage |
| Fate of devices | Survivors are retested and shipped | Stressed samples are not shipped |
| Result | Pass or fail for each device | Failure count, parameter drift, lifetime and FIT estimate |
| When performed | Continuously in production | New product or process qualification and after significant changes |
| Cost character | Recurring cost added to every unit | One-time qualification cost |
The bathtub curve explains both
Plotted over time, the failure rate of a population of chips follows a bathtub shape: high at the start, low and roughly flat in the middle, and rising again at the end of life. Early failures come from latent manufacturing defects such as weak oxide or marginal contacts. Wear-out failures come from mechanisms such as time-dependent dielectric breakdown (TDDB), electromigration and transistor ageing.
Burn-in deliberately uses up the early part of the curve in the factory, so the parts that reach customers start in the flat region. HTOL checks that the right-hand rise begins well beyond the product's required lifetime under use conditions.
How HTOL becomes a lifetime estimate
Temperature accelerates most failure mechanisms. Using an acceleration model such as the Arrhenius relation with an assumed activation energy, each hour at the stress temperature is converted into many hours at the use temperature. A 1,000-hour test can therefore represent years of operation in the field.
The number of failures, together with the equivalent device-hours, gives a failure rate in FIT, the number of failures per billion device-hours, usually quoted at a stated confidence level. JEDEC JESD22-A108 describes the test method for temperature, bias and operating life stresses.
Reducing burn-in, keeping HTOL
Burn-in is effective but costly: it adds time, needs burn-in boards and ovens, and applies stress to good parts as well. Manufacturers therefore try to shorten it or apply it selectively as a process matures, using statistical outlier screening of test data and adaptive test to find suspect parts. Automotive and other high-reliability markets, however, often still require it.
HTOL has no such substitute. It remains a standard element of qualifying a new product or process, and it is repeated when a significant change is made to the design, fab process or package.
FAQ
Can HTOL samples be sold afterwards?
No. HTOL consumes a meaningful part of a device's life by design, and the test is destructive in intent, so the samples are kept for analysis or scrapped.
Why not simply burn in every chip for 1,000 hours?
That would use up useful life, tie up equipment and add large cost to every unit. Burn-in only needs to be long enough to trigger latent defects, which usually happens within hours.
What is wafer-level burn-in?
It is burn-in performed on whole wafers before dicing and packaging. It is used where dies must be proven good before being stacked or assembled into expensive multi-die packages, and it needs special contact technology to power many dies at once.
How do HTOL and burn-in relate to DPPM?
Burn-in lowers the early-failure rate seen by customers, which shows up as fewer defective parts per million (DPPM) in the field. HTOL addresses long-term failure rate, which is expressed in FIT rather than DPPM.
Terms compared
- HTOL (High Temperature Operating Life)An accelerated life test that runs sample devices hot and biased for around 1,000 hours to estimate lifetime and failure rate in FIT.
- Burn-In TestA pre-shipment screen that runs chips hot and at raised voltage so that devices with latent defects fail in the factory instead of in the field.
- Bathtub Curve / FIT RateThe bathtub-shaped plot of failure rate over time, with early, random and wear-out periods; FIT is the unit for the random failure rate.
Japanese companies involved
More test and reliability comparisons
Sources
Semiconductor comparisons
- All semiconductor comparisons
- SEM vs TEM: what is the difference?
- XPS vs EDX: what is the difference?
- Czochralski vs float zone: what is the difference?
- SOI vs bulk silicon: what is the difference?
- Epitaxial wafer vs polished wafer: what is the difference?
- Fabless vs foundry: what is the difference?
- Tokyo Electron vs Applied Materials: what is the difference?
Last updated: November 2, 2026