Epitaxial wafer vs polished wafer: what is the difference?
Device makers buy several kinds of silicon wafer, and the choice between polished and epitaxial is one of the most basic. It sets the defect level in the region where transistors are built and the doping profile the device can rely on.
The short answer
A polished wafer is a slice of a single-crystal ingot that has been lapped and polished, so its surface carries whatever the ingot contained, including grown-in voids such as COPs. An epitaxial wafer has a new single-crystal silicon layer grown on top of a polished substrate, typically a few micrometres thick and much thicker for power devices; the layer is free of COPs and can have a different doping level or type from the substrate. The price of those advantages is the extra epitaxy step.
Side-by-side comparison
| Aspect | Polished wafer | Epitaxial wafer |
|---|---|---|
| How the surface is made | Slicing the ingot, then lapping, etching and polishing | A new single-crystal layer grown by chemical vapour deposition on a polished substrate |
| Grown-in defects (COPs) | Present near the surface unless the crystal is grown defect-free | Absent in the epitaxial layer |
| Doping profile | Fixed by the ingot, varying slightly along its length | Layer and substrate designed independently, for example p- on p+ |
| Oxygen | Contains interstitial oxygen from CZ growth, which supports gettering | Layer is nearly oxygen-free; gettering relies on the substrate |
| Gate oxide integrity | Can be degraded by COPs | Good |
| Cost | Lower; the baseline product | Higher because of the epitaxy step |
| Typical uses | General logic, memory and many other ICs | Advanced CMOS, power devices, image sensors, SiC devices |
| Intermediate option | Annealed wafer: surface COPs removed by high-temperature annealing | Not applicable |
Why power devices need epitaxial wafers
In a vertical power MOSFET or IGBT, the blocking voltage is set by the thickness and doping of the drift layer. An epitaxial wafer provides exactly that structure: a lightly doped layer of controlled thickness on a heavily doped, low-resistance substrate. It follows that non-uniformity in epitaxial thickness and resistivity translates directly into spread in breakdown voltage and on-resistance across the wafer.
In silicon carbide, epitaxy has an additional job. Basal plane dislocations in the substrate can degrade bipolar operation, and growth conditions and buffer layers are designed to convert most of them into less harmful threading edge dislocations before they reach the active layer.
Annealed wafers: the third option
Where only surface COPs need to be removed and no special doping profile is required, an annealed wafer can be used. A polished wafer is heated to about 1,200°C in hydrogen or argon; surface diffusion of silicon atoms fills the near-surface voids and leaves a defect-free layer at lower cost than epitaxy. Annealed wafers were widely used for memory. As makers learned to grow CZ crystals that are practically free of COPs, polished wafers from such crystals became another route to a defect-free surface.
Choosing by what you are paying for
Choosing a polished wafer means accepting the quality of the ingot as it is. Choosing an epitaxial wafer means paying extra for a controlled surface layer and a designed doping profile. The decision rests on the gate oxide reliability required, the doping profile the device needs, where gettering will take place and the price of the end product.
Because changing the wafer type moves both yield and cost for the same design, wafer specifications are usually negotiated in detail between the device maker and the wafer supplier. Japanese wafer makers such as Shin-Etsu Handotai and SUMCO supply polished, annealed and epitaxial wafers.
FAQ
How much more does an epitaxial wafer cost?
There is a clear premium, because each wafer spends time in an epitaxial reactor and consumes process gases. The size of the premium depends on layer thickness, specification and diameter, so there is no single figure; thick power-device layers cost much more than thin CMOS layers.
Does an epitaxial layer remove the need for gettering?
No. The epitaxial layer contains almost no oxygen, so intrinsic gettering has to happen in the substrate below, where oxygen precipitates (bulk micro-defects) capture metal impurities while devices are built in the clean layer above. Heavily doped substrates also act as getters.
Why do image sensors use epitaxial wafers?
Dark current in image sensors is driven by metal contamination and crystal defects. An epitaxial layer offers high crystal quality and precisely controlled doping, while the substrate below provides gettering, which suits sensors that must detect very weak light.
Terms compared
- Epitaxial Wafer (Epi Wafer)A polished silicon wafer with a single-crystal silicon layer, a few to tens of micrometres thick, grown on top with its own doping.
- Silicon WaferA thin, mirror-polished disc of single-crystal silicon on which chips are built; 300 mm is the standard size for leading-edge production.
- Annealed WaferA polished silicon wafer heat-treated at about 1,200 °C in hydrogen or argon to remove near-surface COP defects and create a defect-free layer.
- GetteringTechniques that pull metal impurities such as iron, copper and nickel away from the device layer of a silicon wafer and trap them where they do no harm.
Japanese companies involved
- NuFlare Technology · Electron-beam mask writers, mask inspection and epitaxial reactors
- Shin-Etsu Chemical · Silicon wafers, photoresists and photomask blanks
- SUMCO · Silicon wafers
- Hamai Industries · Lapping and polishing machines for wafers
- Kokusai Electric · Batch deposition, diffusion and ALD equipment
- DISCO · Dicing, grinding and polishing equipment
More wafers and substrates comparisons
Sources
Semiconductor comparisons
- All semiconductor comparisons
- Fabless vs foundry: what is the difference?
- Tokyo Electron vs Applied Materials: what is the difference?
- EUV vs DUV lithography: what is the difference?
- High-NA EUV vs standard EUV: what is the difference?
- Single patterning vs multi-patterning: what is the difference?
- Chemically amplified resist vs metal oxide resist: what is the difference?
- ALD vs CVD: what is the difference?
Last updated: November 2, 2026