Semiconductor Etching Terms Explained: Dry, Wet and Atomic Layer Etch
How material is removed to turn a resist pattern into transistor gates, contacts and deep holes: plasma etching, wet etching, selectivity, aspect ratio and the newer atomic layer etch.
Removing material precisely
Etching removes the film that lithography has left unprotected. Dry (plasma) etching uses reactive ions and radicals to cut vertical walls; wet etching uses liquid chemicals and is isotropic. The key figures are etch rate, selectivity between materials, uniformity across the wafer and the profile of the etched feature.
3D NAND and advanced DRAM need holes and trenches with aspect ratios well above 50:1, which has made high-aspect-ratio etch one of the most demanding steps in the fab.
Japanese suppliers
Tokyo Electron and Hitachi High-Tech make plasma etch systems, and Japanese gas and chemical makers supply many of the etch gases and wet etchants. Plasma-facing parts such as quartz and ceramic rings are also a strong area for Japanese component makers.
All etching terms (27)
- Aspect RatioThe depth-to-width ratio of a trench, via or hole; the higher it is, the harder it is to etch and to fill.
- Aspect Ratio Dependent Etching (ARDE)The slowing of dry etching as holes and trenches become deeper and narrower, also called RIE lag.
- Atomic Layer Etching (ALE)An etching technique that removes material roughly one atomic layer per cycle using two self-limiting steps, giving very precise depth control.
- Bosch ProcessA deep reactive ion etching method that alternates SF₆ etching and C₄F₈ passivation to cut deep, vertical holes in silicon.
- CCP (Capacitively Coupled Plasma)A plasma source that applies RF power between two parallel-plate electrodes, used for dielectric etching and PECVD.
- Charge-upAccumulation of charge from a plasma, ion beam or electron beam on insulators or the wafer surface, causing profile defects and damage.
- DissociationThe breaking of molecular bonds into fragments such as atoms and radicals, driven in plasmas by electron collisions.
- Dry EtchingEtching that removes material in the gas phase with plasma or reactive gases; the main way fine patterns are carved into wafers.
- ECR Plasma (Electron Cyclotron Resonance Plasma)A high-density plasma made by matching microwaves to the gyration frequency of electrons in a magnetic field.
- Etch SelectivityThe ratio between the etch rate of the film being removed and that of the mask or underlying layer that must remain.
- EtchingThe front-end process that removes a film where the resist mask is open, carving the lithography pattern into the wafer.
- Etching EquipmentProcess tools that selectively remove thin films and substrate material from wafers, mostly plasma-based dry etchers plus wet etch systems.
- ICP (Inductively Coupled Plasma)A plasma source that drives RF current through a coil to induce an electric field, giving high-density plasma at low pressure.
- IonisationThe process of turning atoms or molecules into charged ions, usually by removing an electron through electron collisions in a plasma.
- Isotropic and Anisotropic EtchingIsotropic etching removes material equally in all directions; anisotropic etching removes it mainly downward with little sideways etching.
- Langmuir ProbeA small metal electrode inserted into a plasma whose current-voltage curve gives electron density, electron temperature and plasma potential.
- Microloading EffectLocal variation in dry etch rate caused by differences in pattern density or opening size within a chip.
- NotchingA dry etch defect in which the base of a feature is cut sideways where it meets an insulating layer, caused by charging.
- Optical Emission Spectroscopy (OES)Analysis of the light emitted by a plasma, wavelength by wavelength, to identify its species and detect etch endpoints.
- Plasma (Semiconductor Processing)A partly ionised gas of electrons, ions, radicals and neutral molecules, created at low pressure with RF power and used for etching, deposition, ashing and chamber cleaning.
- Plasma DensityThe number of electrons or ions per unit volume in a plasma, usually given per cm³; it largely sets etch and deposition rates.
- Plasma EtchingEtching that uses ions and radicals from a plasma in a vacuum chamber to remove material from the wafer surface.
- Plasma SheathThe thin, positively charged boundary layer between a plasma and a wall, electrode or wafer, where ions are accelerated.
- Reaction ByproductSubstances formed alongside the intended reaction in etching or CVD, which affect chambers, exhaust lines and endpoint detection.
- RIE (Reactive Ion Etching)The main form of dry etching, in which reactive radicals and ions from a plasma act together to remove material vertically and transfer patterns with straight side walls.
- Self-bias (DC Self-bias)The negative DC voltage that develops by itself on an RF-powered electrode or wafer, setting the energy of incoming ions.
- Thomson ScatteringScattering of light by free electrons, used with a laser to measure electron density and temperature in a plasma without touching it.
Etching comparisons
Related pages
Glossary
Etching terms
- Aspect Ratio
- Aspect Ratio Dependent Etching (ARDE)
- Atomic Layer Etching (ALE)
- Bosch Process
- CCP (Capacitively Coupled Plasma)
- Charge-up
- Dissociation
- Dry Etching
- ECR Plasma (Electron Cyclotron Resonance Plasma)
- Etch Selectivity
- Etching
- Etching Equipment
- ICP (Inductively Coupled Plasma)
- Ionisation
- Isotropic and Anisotropic Etching
- Langmuir Probe
- Microloading Effect
- Notching
- Optical Emission Spectroscopy (OES)
- Plasma (Semiconductor Processing)
- Plasma Density
- Plasma Etching
- Plasma Sheath
- Reaction Byproduct
- RIE (Reactive Ion Etching)
- Self-bias (DC Self-bias)
- Thomson Scattering
- Dry etching vs wet etching: what is the difference?
- ICP vs CCP: what is the difference?
- ALE vs RIE: what is the difference?
Last updated: November 1, 2026