EUV vs DUV lithography: what is the difference?
Both are optical lithography: light passes through, or reflects off, a mask and a projection system that shrinks the circuit pattern onto a resist-coated wafer. DUV has been the workhorse of chipmaking since the 1990s and still exposes most layers of most chips. EUV entered volume production at the end of the 2010s for the most critical layers of leading-edge logic and, later, DRAM. The choice between them is made layer by layer, balancing resolution against cost, throughput and process complexity.
The short answer
The core difference is wavelength. EUV (extreme ultraviolet) lithography exposes wafers with 13.5 nm light, which must travel through vacuum and be focused by multilayer mirrors, while DUV (deep ultraviolet) lithography uses 248 nm KrF or 193 nm ArF excimer-laser light that passes through quartz lenses, in air or through a film of water. The shorter wavelength lets EUV print the finest layers in a single exposure, whereas DUV needs immersion and multi-patterning to reach comparable pitches.
Side-by-side comparison
| Aspect | EUV | DUV |
|---|---|---|
| Wavelength | 13.5 nm | 248 nm (KrF) or 193 nm (ArF) |
| Light source | Laser-produced plasma: a high-power CO₂ laser hits tiny tin droplets, which emit EUV light | Excimer gas lasers (krypton fluoride or argon fluoride) |
| Numerical aperture (NA) | 0.33 in current production scanners; 0.55 in High-NA systems | Up to about 0.93 dry; 1.35 with water immersion (ArF only) |
| Optics | Reflective: multilayer molybdenum/silicon mirrors, in vacuum | Refractive: lens elements of fused silica and calcium fluoride, in a purged gas environment |
| Mask | Reflective mask built on a multilayer mirror blank with an absorber pattern | Transmissive quartz mask with a chrome or similar absorber pattern |
| Approximate single-exposure half-pitch (k₁ = 0.3) | About 12 nm at NA 0.33 | About 43 nm for ArF immersion; about 80 nm for KrF |
| Patterning approach for the finest pitches | Often single exposure; double patterning only at the tightest pitches | Self-aligned double or quadruple patterning, or several litho-etch passes |
| Typical use | Critical metal, via and contact layers in leading-edge logic and DRAM | Most remaining layers at all nodes; the main tool for mature and specialty processes |
| Suppliers of production scanners | ASML only, with projection optics from ZEISS | ASML, Nikon and Canon (Canon focuses on KrF and i-line) |
Where the resolution gap comes from
The finest half-pitch an optical system can print is estimated with the Rayleigh criterion, R = k₁ × λ / NA, where λ is the wavelength, NA the numerical aperture of the projection optics and k₁ a process factor that resolution-enhancement techniques push down towards its physical limit of 0.25. With k₁ set to 0.3, ArF immersion (λ = 193 nm, NA = 1.35) gives about 43 nm, while EUV (λ = 13.5 nm, NA = 0.33) gives about 12 nm. These are illustrative figures; real limits depend on illumination, mask design and the pattern type.
DUV has already exhausted its main levers. Immersion lithography raised the NA above 1 by filling the gap between lens and wafer with water, and there is no practical way to go much further. EUV instead cuts the wavelength by a factor of more than 14, so it reaches finer pitches even with a much smaller NA.
Why EUV needs vacuum and mirrors
Light at 13.5 nm is absorbed by almost everything, including air and glass. The whole beam path of an EUV scanner is therefore kept in vacuum, and every optical element, from the collector near the plasma source to the projection optics and the mask itself, is a mirror coated with dozens of alternating molybdenum and silicon layers. Each mirror reflects only part of the light, so a powerful source is needed to deliver enough dose to the wafer.
DUV light at 193 nm and 248 nm passes through high-purity fused silica and calcium fluoride, so DUV scanners use refractive lenses and transmissive masks. This is a mature, well-understood architecture, which is one reason DUV tools are simpler to run and maintain.
Cost: compare steps per layer, not tool prices
An EUV scanner costs considerably more than a DUV immersion scanner, but chipmakers compare the total cost of making a layer. Printing a sub-40 nm pitch with DUV requires self-aligned double or quadruple patterning, adding repeated deposition, etch, clean and metrology steps, extra masks for cutting lines, and more opportunities for defects and overlay error. Where a single EUV exposure replaces such a sequence, the step count, cycle time and yield risk all fall.
That is why leading-edge processes mix the two: EUV for the handful of layers with the tightest pitches, and DUV, mostly ArF immersion, ArF dry and KrF, for the many layers where its resolution is sufficient and its throughput and cost per exposure are better.
Where Japanese suppliers fit
Nikon supplies ArF immersion, ArF dry and KrF scanners, and Canon supplies KrF and i-line steppers and scanners, so both compete in DUV but not in EUV. Gigaphoton makes excimer lasers used as DUV light sources. In EUV, Japanese companies are prominent around the scanner rather than in it: photoresist makers such as JSR, Tokyo Ohka Kogyo and Shin-Etsu Chemical, mask blank makers such as AGC and Hoya, and Lasertec in mask and blank inspection.
FAQ
Can leading-edge chips be made with DUV only?
To a degree. With ArF immersion and self-aligned quadruple patterning, DUV can reach metal pitches in the low 20 nm range, and some 7 nm-class logic has been produced without EUV. The cost is many extra process steps, tighter overlay control and lower yield margins, which is why chipmakers with access to EUV use it for the most critical layers.
Is i-line (365 nm) lithography a form of DUV?
No. The 365 nm i-line from a mercury lamp lies in the near ultraviolet. DUV conventionally refers to the 248 nm KrF and 193 nm ArF excimer-laser wavelengths. i-line tools remain widely used for thick-resist, power-device and packaging layers where fine resolution is not needed.
Does EUV completely replace multi-patterning?
No. EUV removes the need for multi-patterning on many layers, but the very tightest pitches in the most advanced nodes may still use EUV double patterning. High-NA EUV, with NA 0.55, is intended to return some of these layers to single exposure.
Why are EUV resists harder to design than DUV resists?
Each EUV photon carries about 14 times the energy of an ArF photon, so for the same dose there are far fewer photons per feature. Random variation in how many are absorbed causes roughness and occasional missing or bridged features, known as stochastic effects, so EUV resists must absorb light efficiently while keeping blur low.
Terms compared
- EUV (Extreme Ultraviolet)Light with a 13.5 nm wavelength used to print the finest chip patterns; it needs mirrors, vacuum and a tin-plasma light source.
- DUV (Deep Ultraviolet)Ultraviolet light of roughly 100-300 nm; in chipmaking, the 248 nm KrF and 193 nm ArF lasers used in most lithography steps.
- Immersion Lithography (ArFi)ArF lithography with ultrapure water between the lens and wafer, raising the numerical aperture above 1 to print finer patterns.
Japanese companies involved
- HOYA · Mask blanks (including EUV) and photomasks
- AGC · EUV mask blanks and glass materials
- Mitsui Chemicals · EUV pellicles and wafer protection tapes
- JSR · Photoresists and semiconductor materials
- Tokyo Ohka Kogyo (TOK) · Photoresists and high-purity process chemicals
- Rapidus · Leading-edge logic foundry (2 nm, in development)
- Lasertec · EUV mask and mask blank inspection
- Gigaphoton · Excimer laser light sources for lithography
More lithography comparisons
Sources
Semiconductor comparisons
- All semiconductor comparisons
- High-NA EUV vs standard EUV: what is the difference?
- Single patterning vs multi-patterning: what is the difference?
- Chemically amplified resist vs metal oxide resist: what is the difference?
- ALD vs CVD: what is the difference?
- CVD vs PVD: what is the difference?
- PECVD vs LPCVD: what is the difference?
- MOCVD vs MBE: what is the difference?
Lithography terms
- All lithography terms
- High-NA EUV vs standard EUV: what is the difference?
- Single patterning vs multi-patterning: what is the difference?
- Chemically amplified resist vs metal oxide resist: what is the difference?
- Bottom Anti-Reflective Coating (BARC)
- Chemically Amplified Resist (CAR)
- Coater/developer
- Coulomb Effect
Last updated: November 2, 2026